S5720-56C-PWR-EI-AC Huawei Quidway S5700 Series Switch (Refurbished)

S5720-56C-PWR-EI-AC Huawei Quidway S5700 Series Switch (Refurbished)

R 15,000.00
S5720-56C-PWR-EI-AC 48 x 10/100/1,000 Base-T Ethernet ports and 4 x 10G SFP+ ports PoE+ One extended slot Double hot-swappable AC/DC...
  • Sold By: Asetos Computers
  • Categories Network Switches, Networking Devices, PoE Network Switches
  • Type: Networking Equipment

S5720-56C-PWR-EI-AC

  • 48 x 10/100/1,000 Base-T Ethernet ports and 4 x 10G SFP+ ports
  • PoE+
  • One extended slot
  • Double hot-swappable AC/DC power supplies, one AC/DC power module is configured by default
  • Forwarding performance: 162 Mpps
  • Switching capacity: 598 Gbit/s

Version Mapping

Table 4-840 lists the mapping between the S5720-56C-PWR-EI-AC1 chassis and software versions.

Table 4-840  Version mapping

Series

Model

Software Version
S5720-EI S5720-C-EI S5720-56C-PWR-EI-AC1

V200R007C00 and later versions

NOTE:
This model does not match V200R007C10.

Appearance and Structure

Figure 4-339  S5720-56C-PWR-EI-AC1 appearance 
1 Forty-eight PoE+ 10/100/1000BASE-T ports 2 Four 10GE SFP+ ports
3 One ETH management port 4 One mini USB port
5 One console port
NOTE:
It is used with a console cable. The console cable is not delivered with the switch and needs to be separately purchased if needed.
6 One USB port
7 Ground screw
NOTE:
It is used with a ground cable.
8 ESN label
NOTE:

You can draw it out to view the ESN and MAC address of the switch.

9 Rear card slot 10 Fan slot
NOTE:

Applicable fan module: FAN-028A-B Fan Module

11 Power module slot 2
NOTE:
Applicable power module:
12 Power module slot 1
NOTE:
Applicable power module:

Port Description

10/100/1000BASE-T port
A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-841 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-841  Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3, IEEE802.3u, IEEE802.3ab

Working mode

10/100/1000 Mbit/s auto-sensing

Maximum transmission distance

100 m

10GE SFP+ port
A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-842 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 4-842  Attributes of a 10GE SFP+ port

Attribute

Description

Connector type

LC/PC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ae

Working mode

GE/10GE auto-sensing

Console port
The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-843.
Table 4-843  Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

Mini USB port

The mini USB port is connected to a console for on-site configuration. When both the Mini USB and console port have a cable connected, only the Mini USB port works.

ETH management port
You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 4-844 describes the attributes of an ETH management port.
Table 4-844  Attributes of an ETH management port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3

Working mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m

In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see "Logging In to a Device for the First Time" in the Configuration Guide - Basic Configuration. If you have logged in to the device for the first time by pressing and holding the MODE button for 6 seconds or longer and save the configuration, the default configuration on the ETH port will be cleared. In this case, you cannot log in to the switch for the first time through the ETH port. You are advised to log in to the switch for the first time through the ETH port.
USB port
The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port of the S5720-EI does not support USB 1.1 and can only connect to a USB flash drive that complies with USB 2.0.
 NOTE:
USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5720-56C-PWR-EI-AC1 has the same types of indicators as the S5720-36C-PWR-EI-AC. For details, see Indicator Description.

Power Supply Configuration

The S5720-56C-PWR-EI-AC1 is a PoE switch. It has two power module slots and uses 1150 W AC PoE power modules or 1000 W AC PoE power modules (applicable in V200R013C00 and later versions). A 1150 W AC PoE power module and a 1000 W AC PoE power module can be used together. Table 4-845 lists its power supply configurations.

Table 4-845  Power supply configurations
Power Module 1 Power Module 2 Available PoE Power Maximum Number of Ports (Fully Loaded)
1150 W (220 V) - 785.4 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 26
1150 W (220 V) 1150 W (220 V) 1440 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 48
1150 W (110 V) - 446.6 W
  • 802.3af (15.4 W per port): 29
  • 802.3at (30 W per port): 14
1150 W (110 V) 1150 W (110 V) 893.2 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 29
1000 W (220 V) - 754.6 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 25
1000 W (220 V) 1000 W (220 V) 1440 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 48
1000 W (110 V) - 754.6 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 25
1000 W (110 V) 1000 W (110 V) 1440 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 48
1000 W (220 V) 1150 W (220 V) 1440 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 48
1150 W (220 V) 1000 W (220 V) 1440 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 48
1000 W (110 V) 1150 W (110 V) 893.2 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 29
1150 W (110 V) 1000 W (110 V) 893.2 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 29
 NOTE:
When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.
Figure 4-340 shows the power supply mode of dual AC PoE power modules (PWR1 and PWR2). After AC power is transmitted to the PWR modules, the PWR modules provide 12 V and -53 V outputs. The outputs are combined on the motherboard, which then provides 12 V voltage for the switch and -53 V voltage for the PDs.
Figure 4-340  Power supply by dual AC PoE power modules 

L: live wire

N: neutral wire

PGND: protection ground

GND: 12 V reference ground

RTN: -53 V reference ground

Heat Dissipation

The S5720-56C-PWR-EI-AC1 uses pluggable fan modules for forced air cooling. Air flows in from the left and right sides, and exhausts from the rear panel.

Technical Specifications

Table 4-846 lists technical specifications of the S5720-56C-PWR-EI-AC1.

Table 4-846  Technical specifications

Item

Description

Memory (RAM)

2 GB

Flash

512 MB in total. To view the available flash memory size, run the display version command.

Mean time between failures (MTBF)

51.34 years when no card is configured; 48.63 years when a 2-port 10GE SFP+ interface card is configured; 47.71 years when a 2-port 10GE RJ45 interface card is configured; 47.79 years when a stack card is configured

Mean time to repair (MTTR)

2 hours

Availability

> 0.99999

Service port surge protection

  • Service ports on front panel: ±6 kV in common mode
  • Ports on the 2-port 10GE RJ45 rear interface card: ±2 kV in common mode

Power supply surge protection

  • Using 1000 W AC power modules: ±6 kV in differential mode, ±6 kV in common mode
  • Using 1150 W AC power modules: ±2 kV in differential mode, ±4 kV in common mode

Dimensions (W x D x H)

442.0 mm x 420.0 mm x 44.4 mm (17.4 in. x 16.5 in. x 1.74 in.)

When 1150 W power modules are installed, they stretch out from the chassis. Therefore, the total depth of the switch changes to 507.3 mm (19.97 in.).

Weight (including packaging materials)

10.9 kg (24.03 lb)

Stack ports

  • Ports on the 2-port 10GE SFP+ rear interface card
  • Ports on the 2-port 10GE RJ45 rear interface card
  • Ports on the 2-port QSFP+ rear stack card

RTC

Supported

RPS

Not supported

PoE

Supported

Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

Maximum power consumption (100% throughput, full speed of fans)

  • Not providing the PoE function: 91.6 W
  • 100% PoE loads: 1564.8 W (system power consumption: 124.8 W, PoE: 1440 W)
Typical power consumption (30% of traffic load)
  • Tested according to ATIS standard
  • EEE enabled
  • No PoE power consumption
  • 53.5 W (without subcard)
  • 61.12 W (with 2*10G optical subcards)
  • 65.85 W (2*QSFP+ stack cards)
  • 69.3 W (with 2*10G electrical subcards)

Operating temperature

0°C to 45°C (32°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.)

NOTE:

When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

Short-term operating temperature

-5°C to +50°C (23°F to 122°F) at an altitude of 0-1800 m (0-5906 ft.)

NOTE:

When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

The equipment can operate beyond the normal operating temperature range for a short-term period, but the following conditions must be met:
  • The equipment operates at a temperature of over 45°C (113°F) consecutively for at most 96 hours in one year.
  • The equipment operates at a temperature of over 45°C (113°F) for a total of no more than 360 hours in one year.
  • The equipment operates at a temperature of over 45°C (113°F) for no more in 15 times in one year.
The equipment may be damaged or experience unexpected exceptions if any of the preceding limits is exceeded.

The equipment cannot start when the temperature is lower than 0°C (32°F). The maximum distance of optical modules used in these conditions cannot exceed 10 km.

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 61.7 dBA

Relative humidity

5% to 95%, noncondensing

Operating altitude

0-5000 m (0-16404 ft.)

Certification

  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

02359578

Terms and conditions of use;
By placing an order with us you agree to our sales terms, conditions and policies.


Application of Terms; Customer Acknowledgment
These Terms constitute a binding contract between the Customer and Asetos. The Customer acknowledges agreement and acceptance of these Terms by making a purchase, placing an order or otherwise shopping on our Website. These Terms are subject to change without prior notice.


Purchase price
Prices are listed on our Web site, and are subject to change without notice. All prices INCLUDE VAT unless otherwise stated.


Shipping; Risk of Loss
During working hours, orders are usually processed within 2-3 hours. However, please allow up to 24 hours for your order to be processed. Asetos typically ships out orders within one business day after they have been placed (this excludes weekends & public holidays). We try our best to ship out all orders the same day if they are paid for before 12pm. You will receive a shipping confirmation email (with a tracking number) as soon as your order has been processed and shipped.

We ship countrywide, to your door. We use a COURIER SERVICE. This is overnight (next BUSINESS day service) to major centers (2-3 days extra to REGIONAL centers), but can take a few days to outlying areas. Please note - large items (over 2kg) might take an extra 1-2 days shipping time.

All times stated above exclude weekends & public holidays.

Asetos charges shipping and handling fees for every shipment, unless a special promotion or contract term provides otherwise; such cost includes the freight charged by the carrier, packaging, and handling. Delivery times are estimates only and we shall not be liable for any delays caused by the courier company or post office.

PLEASE NOTE - We can not ship to certain townships, farms, plots or extreme outlying areas.

Payment is due before shipment, unless credit terms have been arranged in advance. No item will be shipped out until Proof of Payment has been emailed to info@asetos.co.za or faxed to 0866 122 789. We allow a maximum of 5 days to complete order payment. Failure to do so will result in the order being cancelled.


Pricing Information; Availability; Errors and omissions Disclaimer
All pricing is subject to change. We reserve the right to make adjustments to pricing, products and service offerings for reasons including, but not limited to, changing market conditions, product discontinuation, product unavailability, manufacturer price changes and errors in advertisements.

All orders are subject to product availability. Therefore, we cannot guarantee that we will be able to fulfil customer's orders.

We make every effort to ensure the accuracy of the information published on our Website. However, the documents and graphics published on this site may contain technical inaccuracies or typographical errors. We make no representations about the suitability of the information and graphics presented on this site. All such documents and graphics are provided "as is" without warranty of any kind.

If an error is made and a product is listed at an incorrect price, we shall maintain the right to refuse or cancel any orders placed at the incorrect price. If the order has been confirmed and you have paid, we shall immediately issue a credit. We also do not guarantee that our prices listed on other websites are accurate or up-to-date.


Limitation of Liability
NEITHER ASETOS NOR ITS AFFILIATES WILL BE LIABLE FOR LOST PROFITS, LOSS OF BUSINESS OR OTHER CONSEQUENTIAL, SPECIAL, INDIRECT OR PUNITIVE DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY THIRD PARTY. NEITHER ASETOS NOR ITS AFFILIATES WILL BE LIABLE FOR PRODUCTS NOT BEING AVAILABLE FOR USE OR FOR LOST OR CORRUPTED DATA OR SOFTWARE OR THE PROVISION OF SERVICES BY THIRD PARTIES. THE CUSTOMER AGREES THAT FOR ANY LIABILITY RELATED TO THE PURCHASE OF PRODUCTS OR SERVICES PROVIDED DIRECTLY BY ASETOS OR ITS AFFILIATES, NEITHER ASETOS NOR ITS AFFILIATES WILL BE LIABLE OR RESPONSIBLE FOR ANY AMOUNT OF DAMAGES ABOVE THE RAND AMOUNT PAID BY CUSTOMER FOR THE PRODUCT(S) OR SERVICE(S) GIVING RISE TO THE CLAIM.

We will not be responsible for any delays in delivery which result from any circumstances beyond our control, including without limitation, product unavailability, carrier delays, delays due to fire, severe weather conditions, failure of power, labour problems, acts of war, terrorism, general insurrection, acts of God or acts of any government or agency.

We will not be held responsible for any typographical errors including instructions, descriptions, prices or terms.

We will not be held responsible for missing, damaged, or late package delivery by the shipper.


Orders; Payment Terms

Payment is due before shipment, unless credit terms have been arranged in advance. No item will be shipped out until Proof of Payment has been emailed to nfo@asetos.co.za or faxed to 0866 122 789. We allow a maximum of 5 days to complete order payment. Failure to do so will result in the order being cancelled.


Return of merchandise (RMA) and Warranty
All new items are covered by a 6 month warranty which will be honoured directly by Asetos. All products will either be replaced/repaired/refunded depending on stock availability. There is no warranty on used items unless stated otherwise.

Please email us should you need to return an item.

We do not reimburse your fee to ship to us, but we will pay for return shipping if the item is subject to replacement.

Refunds are subject to inspection of item(s) and all returns are subject to a 20% restocking fee if item is no longer in BRAND NEW condition

Please re-package safely and include all original product packaging.

Asetos reserves the right to refuse a refund if the item is damaged from misuse, items are missing, or if the product is altered in any way.

Asetos or its affiliates are not responsible for damage or loss of any kind that may occur as a result of using or misusing any product purchased from us.


Privacy and Security
Asetos respects your personal privacy!

Any information about you, your email address, your purchases, etc. is kept confidential and NOT given or sold to ANY third party for ANY reason (unless required by a government office or by a court order).

Recently Viewed Products

We Accept